Agilent Technologies E1364A User Manual Download Page 13 | Manualshive

Page: 13 / 76

background image

Chapter 1

Getting Started with the Agilent E1364A

Using This Chapter

This chapter includes a Form C Switch description, addressing guidelines,
and an example program to check initial operation. Chapter contents are:

•

Instrument Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11

•

Programming the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 13

•

Initial Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 15

Instrument Definition

Agilent plug-in modules installed in an Agilent mainframe are treated as
independent instruments each having a unique secondary GPIB address.
Each instrument is also assigned a dedicated error queue, input and output
buffers, status registers and, if applicable, dedicated mainframe memory
space for readings or data. An instrument may be composed of a single
plug-in module or multiple plug-in modules (for a Switchbox or Scanning
Voltmeter Instrument).

Switch Description

The Agilent E1364A 16-Channel Form C Switch Module is a B-Size
VXIbus and VMEbus register-based product which can be used for
switching/scanning, control, and digital output applications. The switch can
operate in a B-Size VXIbus or VMEbus mainframe or (with an adapter) in a
C-Size VXIbus mainframe. The module has 16 channels of Form C relays.
Each channel includes a relay with common (C), normally open (NO), and
normally closed (NC) contacts.

For the Form C Switch, switching consists of opening or closing a channel
relay to provide alternate connections to user devices. Scanning consists of
closing a set of relays, one at a time. By adding jumpers and
pullup/pulldown resistors, the switch can be used to control external user
devices or as a digital output device.

Basic Operation

As shown in Figure 1-1, the Form C Switch consists of 16 channels
(channels 00 through 15). Each channel uses a latching relay. As required,
jumpers can be added to c5 V or +12 V for control or digital output
applications. Also, pullup resistors can be added for digital output
applications.

Chapter 1

Getting Started with the Agilent E1364A 11

«
...
11
12
13
14
15
...
»

Summary of Contents for E1364A













































































Reviews:

No comments

Related manuals for E1364A

Brand: D-Link Pages: 357

Brand: KELCO Pages: 2

Brand: Nectarine Health Pages: 9

Brand: Indu-Sol Pages: 9

Brand: H3C Pages: 57

Brand: Quintech Pages: 2

Brand: N-Tron Pages: 16

Brand: Lantech Pages: 24

kontron KSwitch D3 UM

Brand: S&T Pages: 38

Brand: Hailink Pages: 6

Brand: Clare Controls Pages: 2

Brand: Woxcon Pages: 51

GTB-MHDMI1.3-442

Brand: Gefen Pages: 29

Brand: Gefen Pages: 20

Brand: NightStick Pages: 2

Brand: Quintum Pages: 125

Brand: Comelit Pages: 8

Brand: PairGain Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands