Agilent Technologies E1364A User Manual Download Page 52 | Manualshive

Page: 52 / 76

background image

:CONTinuous?

INITiate:CONTinuous?

queries the scanning state. With continuous

scanning enabled, the command returns 1. With continuous scanning
disabled, the command returns 0.

Example

Query Continuous Scanning State:
This example enables continuous scanning of a switchbox and queries the
state. Since continuous scanning is enabled, INIT:CONT? returns 1.

INIT:CONT ON

Enable continuous scanning

INIT:CONT?

Query continuous scanning

[:IMMediate]

INITiate[:IMMediate]

starts the scanning process and closes the first channel

in the channel list. Successive triggers from the source selected by the
TRIGger:SOURce command advance the scan through the channel list.

Comments

•

Starting the Scanning Cycle: The INITiate[:IMMediat] command
starts scanning by closing the first channel in the channel list. Each
trigger received advances the scan to the next channel in the channel
list. An invalid channel list definition causes an error (see
[ROUTe:]SCAN).

•

Stopping Scanning Cycles: See ABORt.

Example

Enabling a Single Scan:
This example enables a single scan of channels 00 through 03 of a
single-module switchbox. The trigger source to advance the scan is
immediate (internal) triggering set with (default) TRIGger:SOURce
IMMediate.

SCAN (@100:103)

Scan channels 00-03

INIT

Begin scan, close channel 00 (use
immediate triggering).

50 Agilent E1364A Form C Switch Command Reference

Chapter 5

«
...
50
51
52
53
54
...
»

Summary of Contents for E1364A













































































Reviews:

No comments

Related manuals for E1364A

SmartPro DGS-1500-20

Brand: D-Link Pages: 113

xStack DGS-3120 Series

Brand: D-Link Pages: 1150

Brand: CALIENT Pages: 22

Brand: 3Com Pages: 8

Brand: Datavideo Pages: 58

Brand: Sams Pages: 10

4-Port PoweredUSB 2.0 Hub 011006

Brand: CyberData Pages: 4

Brand: Matrix Switch Corporation Pages: 60

Brand: Vega Pages: 28

Brand: J-Tech Digital Pages: 28

Brand: Generac Power Systems Pages: 20

Brand: A-Neuvideo Pages: 26

ServSwitch KV1510A

Brand: Black Box Pages: 16

Brand: Eaton Pages: 5

Brand: Alloy Pages: 33

Brand: Thinklogical Pages: 17

RPT-2012/P-4F-T-1 Series

Brand: Subject Link Pages: 2

Brand: APG Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands