Agilent Technologies Acqiris DC110 User Manual Download Page 24 | Manualshive

Page: 24 / 66

background image

User Manual: Family of 8-bit Digitizers

Page 24 of 66

3.

Turn on the power of the crate(s), if present, and then the PC and start the operating system.

NOTE: Acqiris Digitizers are equipped with a LED. If this LED is not glowing orange or red when the power is
applied there is a severe problem. Either the module is broken or the necessary voltages for its use are not
available.

NOTE:

For proper system operation when using the IC200, IC414, or other PCI extension interface to connect

a CC10X crate to a remote PC, the crate must be powered on before the PC in order for the PC BIOS to
recognize the presence of the CompactPCI crate.

4.

Devices that were installed using a previous version of

Acqiris Software

the instruments in these logical

positions will still appear as

Unknown Devices

. This can be changed to the new Acqiris type category with

the Grey Diamond icon by

Uninstall

ing the device and then

Installing

again. Instructions on this procedure

can be found in the

ReadMe.txt

file in the

manuals

folder of your Acqiris Software installation.

2.5.

After Restarting

2.5.1.

Windows 2000

Under Windows 2000, you

must

login with administrator privileges after the first boot following the hardware

installation; the Plug&Play system must have the appropriate privileges to be able to complete your hardware
installation successfully. After a successful hardware installation, you will be able to use your Acqiris Digitizer(s)
with normal privileges.

At the first boot following the hardware installation, Windows will detect the new hardware and will install the
devices automatically. The following image will appear.

NOTE: In some systems an application program (such as AcqirisLive) will not yet work correctly at this point. One
additional boot cycle may be needed if this is the first time that a hardware board is being installed.

2.5.2.

Windows XP

Under Windows XP, you

must

login with administrator privileges after the first boot following the hardware

installation; the Plug&Play system must have the appropriate privileges to be able to complete your hardware
installation successfully. After a successful hardware installation, you will be able to use your Acqiris Digitizer(s)
with normal privileges.

If you login with administrator privileges after the first boot following the hardware installation, Windows will detect
the new hardware and start the “Found New Hardware Wizard” after a few seconds.

«
...
22
23
24
25
26
...
»

Summary of Contents for Acqiris DC110



































































Reviews:

No comments

Related manuals for Acqiris DC110

Brand: Accurate Logic Pages: 50

Acuvim-L Series

Brand: AccuEnergy Pages: 188

Brand: VAMP Pages: 78

Brand: FARMSCAN Pages: 28

Brand: Keithley Pages: 138

Brand: NCTE Pages: 10

Brand: SAGEMCOM Pages: 33

Brand: Xylem Pages: 19

Brand: HANSA-FLEX Pages: 23

iTrans 77023554

Brand: Industrial Scientific Pages: 94

Brand: Hanna Instruments Pages: 12

Brand: ScienTECH Pages: 44

Brand: LaserLine Pages: 11

Brand: 3nh Pages: 32

Brand: OHAUS Pages: 63

Brand: U.S. Divers Pages: 63

Brand: S.E. International Pages: 2

Brand: Riken Keiki Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands