manualshive.com logo in svg

Agilent Technologies Acqiris DC110, User Manual

Share
Download
Agilent Technologies Acqiris DC110 User Manual Download Page 42

 

 

User Manual: Family of 8-bit Digitizers 

 

Page 42 of 66 

Other controls in the control panel allow you to select the optimal acquisition settings for your particular signal. Each 
of the other control panel functions will be discussed in detail in the following Control Panel Functions section. Here 
is a sample result. 

 

 

4.2.

 

Control Panel and Functions 

4.2.1.

 

Control Panel Mode 

In AcqirisLive there are two control panel modes available, Oscilloscope Mode and Transient 
Recorder Mode. The choice of mode is entirely determined by the preference of the user. 

DSO TR 

Both modes provide the same set of functional capabilities but display the settings slightly differently. 

For example in Transient Recorder Mode, the user selects the Full Scale Range of the amplifier whereas in 
Oscilloscope Mode the user selects the input voltage scale set in Volts/Div. The desired mode is selected using one 
of the two buttons shown at the top of the control panel. The distinction between the control panels for the two 
operating modes can be seen in the images below. 

In both modes it is possible to set the memory depth and the sample speed independently within the limits of the 
maximum available memory. However the two modes differ in the following way.  

In Oscilloscope Mode, the user selects the time window (time per div) and the sampling rate will be adjusted to the 
fastest possible within the limits of the available memory. The maximum available memory is programmable. 

In Transient Recorder Mode, the user selects the capture time window, the sampling rate, or the number of samples. 
When selecting the capture time window, the number of samples is adapted, keeping the current sampling rate and 
number of segments, up to the maximum available memory on the card. When selecting the sampling rate, the 
number of samples is adapted, keeping the current capture time window and number of segments, up to the 
maximum available memory on the card. When selecting the number of samples, the capture time window is 
adapted, keeping the current sampling rate and number of segments. 

Summary of Contents for Acqiris DC110



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands