manualshive.com logo in svg

Agilent Technologies 700 Series, User Manual

Share
Download
Agilent Technologies 700 Series User Manual Download Page 45

 

Maintenance and Troubleshooting 

Agilent 700 Series ICP Optical Emission Spectrometers User’s Guide 

45 

Weekly 

 

Clean the torch.  

 

Clean the cone (710/720 ICP-OES instruments). 

 

Clean the snout (715/725 ICP-OES instruments). 

 

Clean the bonnet (715/725 ICP-OES instruments). 

 

Clean the spraychamber. 

 

Clean the nebulizer. 

Monthly 

 

Clean the cooling air intake filter on top of your instrument. 

 

Inspect the state of the induction coil. Contact your local Agilent 
office or representative if maintenance is required. See the 
following section for additional information. 

 

Remove and clean the water filter on the back of the instrument. 

 

Check the water level in the water cooler (refer to the manual 
supplied with the water cooler for details). 

 

Check/clean the heat exchanger (radiator) on the cooling system 
to remove any build-up of dust and dirt. 

 

Periodically, drain the coolant from the cooling system and then 
refill/ treat with an appropriate algaecide (as recommended by 
the manufacturer). 

 

Perform a wavelength calibration.

 

Inspect the external gas supply system for leaks including the 
tubing connected to the instrument. Replace any damaged, 
leaking or worn components. 

Summary of Contents for 700 Series



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands