manualshive.com logo in svg

Agilent Technologies 700 Series, User Manual

Share
Download
Agilent Technologies 700 Series User Manual Download Page 19

 

Introduction 

Agilent 700 Series ICP Optical Emission Spectrometers User’s Guide 

19 

Environmental Conditions 

The instrument is suitable for indoor use 

only

 and is classified 

suitable under the following categories (EN 61010-1): 

 

Installation category II 

 

Pollution degree 2 

 

Equipment class I 

Temperature Control 

For 

optimum analytical performance

, it is recommended that the 

ambient temperature of the laboratory be between 20 and 25 °C (68 
and 77 °F).and be held constant to within 

±

2 °C (

±

3.6 °F) throughout 

the entire working day. 

Electrical Power Supplies 

For electrical requirements, refer to your Agilent 700 Series ICP 
Optical Emission Spectrometers Site Preparation Guide. 

Fuses 

1FS1 and 1FS2 

T6.3 AH 250 V, IEC 127 sheet 5, 5 x 20 mm 

1CB1 

Circuit breaker 30 A Fast trip 

NOTE 

For safety reasons, any other internal fuse or circuit breaker is not operator 
accessible, and should only be replaced by Agilent-authorized personnel. 

 

Fuse information on the rear of the instrument is the most up to 
date. 

 

 

Summary of Contents for 700 Series



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands