manualshive.com logo in svg

Agilent Technologies 6850 GC, Install Manual, Page: 18 / 20

Share
Download
Agilent Technologies 6850 GC Install Manual Download Page 18

18

Installing Sampling Valves

Installing Sampling Valves on an Agilent 6850 Gas Chromatograph

2

Connect the control cable.

•

Connect the cable from the control 
valve to the wiring harness.

3

Install the modified top cover.

a

Place the modified lid top cover 
supplied in this kit on top of the lid.

b

Secure with eight screws.

4

Connect the external actuator air 
supply tubing.

a

Connect the air source to the fitting on 
the back of the lid (the control valve).

b

Set the source delivery pressure at 310 
to 345 kPa (45 to 50 psi).

•

Valves are gas-driven, usually by 
compressed air. There is no high 
purity requirement for this gas. The 
supply pressure may surge as the 
valve operates, so the actuator gas 
must not come from the FID air.

5

Finishing up.

a

Restore carrier and other gases to the 
instrument.

b

Restore power.

c

Apply your normal operating 
procedures. Leak-check all new 
connections.

Table 5

Installing an air control valve for a rotary-type sampling valve (continued)

Step

Action

Notes

Harness

Connector

Summary of Contents for 6850 GC





















Reviews:

No comments