manualshive.com logo in svg

Agilent Technologies 5977B CI MSD, Operating Manual

The Agilent Technologies 5977B CI MSD is an advanced scientific instrument offering precise and reliable mass spectrometry analysis. To ensure optimal usage, download the comprehensive Operating Manual for free from our website. This user-friendly manual provides detailed instructions and troubleshooting insights for maximizing the capabilities of the 5977B CI MSD.

Share
Download
background image

8

CI  Maintenance

To Disassemble the CI Source

238

5977B Series MSD Operating Manual

To Disassemble the CI Source

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Hex ball driver, 1.5 mm (8710-1570)

•

Hex ball driver, 2.0 mm (8710-1804)

•

Wrench, open-end, 10 mm (8710-2353)

•

Nut driver, 5.5 mm (8710-1220)

•

Tweezers (8710-2460)

Procedure

Refer to the exploded parts view 

Figure 78

 and CI source parts list 

Table 24

 on 

page 239 while using this procedure.

1

Remove the CI source. (See

“To Remove the CI Source” 

on page 235.)

2

Remove the filaments. (See

“To Remove the CI Source Filament” 

on 

page 247.)   

3

Separate the source heater assembly from the source body. The source 
heater assembly includes the source heater, repeller, and related parts.

4

Disassemble the repeller assembly by removing the ceramic insulator from 
the repeller.

5

Remove the setscrew securing the lenses to the source body.

6

Pull the lenses out of the source body and separate the lens insulator, ion 
focus lens, drawout cylinder, drawout lens, and entrance lens.

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

umbra pompe SAL 35 Operating Instructions Manual preview
SAL 35
Brand: umbra pompe Pages: 16
A.O. Smith 305 Specification Sheet preview
305
Brand: A.O. Smith Pages: 2
Bacharach QV2 Operation And Maintenance Instruction Manual preview
QV2
Brand: Bacharach Pages: 12
Samson KL Series Directions For Use Manual preview
KL Series
Brand: Samson Pages: 8
ICP EDM Series Installation Instructions Manual preview
EDM Series
Brand: ICP Pages: 9
EasyPro PA10 Installation, Operating And Maintenance Instructions preview
PA10
Brand: EasyPro Pages: 8
Radiant 135RAD3N Owner'S Manual preview
135RAD3N
Brand: Radiant Pages: 24
Dux Proflo 125S1 Owner'S Manual preview
Proflo 125S1
Brand: Dux Pages: 20
STIEBEL ELTRON DHH 12 Si control Operating And Installation preview
DHH 12 Si control
Brand: STIEBEL ELTRON Pages: 168
ABS Sanisett Operating Instructions Manual preview
Sanisett
Brand: ABS Pages: 10
NAVAC NRRD User Manual preview
NRRD
Brand: NAVAC Pages: 8
D-D The Aquarium Solution P1+ Quick Start Manual preview
P1+
Brand: D-D The Aquarium Solution Pages: 8
salmson NOEH Installation And Operating Instructions Manual preview
NOEH
Brand: salmson Pages: 48
Parkside PKA 20-Li B2 Translation Of The Original Instructions preview
PKA 20-Li B2
Brand: Parkside Pages: 195
Daikin Altherma 3 R MT F User Reference Manual preview
Altherma 3 R MT F
Brand: Daikin Pages: 68
Hospira GemStar Series System Operating Manual preview
GemStar Series
Brand: Hospira Pages: 221
SAMES KREMLIN REXSON 2B750 User Manual preview
REXSON 2B750
Brand: SAMES KREMLIN Pages: 50
Nortek 024KA Installation Instructions Manual preview
024KA
Brand: Nortek Pages: 16

Brands by name

Popular brands

Load more brands