Agilent Technologies 5977B CI MSD Operating Manual Download Page 235

Page: 235 / 254

CI Maintenance



To Remove the CI Source

5977B Series MSD Operating Manual

235

To Remove the CI Source

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Tweezers (8710-2460)

Procedure

The video shows wiring connections for the non-HES model MSD.

Vent the MSD. (See

“To Vent the MSD”

on page 136.)

Open the analyzer chamber. (See

“To Open the Analyzer Chamber”

page 176.)

Use tweezers to disconnect the wires from the CI source. Do not bend the
wires any more than necessary. (See

“To Connect/Disconnect non-HES

Model Wiring from the CI Source”

on page 236 or

“To Connect/Disconnect

EI HES Model Wiring to the CI Source”

on page 237.)

Trace the wires for the ion source heater and temperature sensor to the ceramic
source board, and disconnect them there. (See

“To Connect/Disconnect EI HES

Model Wiring to the CI Source”

on page 237.)

Remove the two large thumbscrews that hold the ion source in place.

Pull the ion source out of the source radiator, and place it in its storage container.



WARNING

The analyzers, GC/MSD interface, and other components in the analyzer
chamber operate at very high temperatures. Do not touch any part until you
are sure it is cool.

CAUTION

Always wear clean gloves to prevent contamination when working in the
analyzer chamber.

CAUTION

Make sure you use an antistatic wrist strap, and take other antistatic
precautions before touching analyzer components.

CAUTION

When disconnecting leads, pull on the connectors, not on the wires.



Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands