Agilent Technologies 5977B CI MSD Operating Manual Download Page 247

Page: 247 / 254

CI Maintenance



To Remove the CI Source Filament

5977B Series MSD Operating Manual

247

To Remove the CI Source Filament

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Hex ball driver, 1.5 mm (8710-1570)

•

Tweezers (8710-2460)

Procedure

Vent the MSD. (See

“To Vent the MSD”

on page 136.)

Open the analyzer chamber. (See

“To Open the Analyzer Chamber”

page 176.)

Remove the CI source. (See

“To Remove the CI Source”

on page 235.)

Remove the screw holding the filament to the CI source body. (See

Figure 81

Slide the filament off the CI source assembly. (See

Figure 81





CAUTION

Always wear clean gloves to prevent contamination when working in the
analyzer chamber.

WARNING

The analyzer, GC/MSD interface, and other components in the analyzer
chamber operate at very high temperatures. Do not touch any part until you
are sure it is cool.

Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands