Agilent Technologies 5977B CI MSD Operating Manual Download Page 192

Page: 192 / 254

General Maintenance



To Remove the EI HES filaments

192

5977B Series MSD Operating Manual

To Remove the EI HES filaments

Materials needed

•

Gloves, clean, lint-free

•

Large (8650-0030)

•

Small (8650-0029)

•

Cloths, clean (05980-60051)

•

T6 Torx driver, (8710-2548)

Procedure

Vent the MSD. (See

“To Vent the MSD”

on page 136.)

Open the analyzer chamber. (See

“To Open the Analyzer Chamber”

page 176.)

Remove the ion source and place it on a clean cloth on your work surface.
(See

“To Remove the EI HES”

on page 178.)

Remove the screw securing the filament block to the source mount. (See

Figure 62



CAUTION

Always wear clean gloves to prevent contamination when working in the
analyzer chamber.

WARNING

The analyzer, GC/MSD interface, and other components in the analyzer
chamber operate at very high temperatures. Do not touch any part until you
are sure it is cool.

Figure 62 Replacing the dual filament

Source mount

Screw

Filament block

Dual filament



Summary of Contents for 5977B CI MSD































































































































































































































































Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands

Agilent Technologies 5977B CI MSD, Operating Manual

Search results

Summary of Contents for 5977B CI MSD

Reviews:

Related manuals for 5977B CI MSD

Brands by name

Popular brands