manualshive.com logo in svg

Agilent Technologies 5977B CI MSD, Operating Manual

The Agilent Technologies 5977B CI MSD is an advanced scientific instrument offering precise and reliable mass spectrometry analysis. To ensure optimal usage, download the comprehensive Operating Manual for free from our website. This user-friendly manual provides detailed instructions and troubleshooting insights for maximizing the capabilities of the 5977B CI MSD.

Share
Download
background image

1

Introduction

MSD Hardware Description

5977B Series MSD Operating Manual

19

MSD Hardware Description

The Agilent 5977B MSD can be paired with one of several Agilent GCs (See 

Figure 1

).

In this manual, the term “CI MSD” refers to the G7078B MSD or to the G7077B, 
G7079B, and G7081B models that were field upgraded for CI operation. It also 
applies, unless otherwise specified, to the flow modules for these instruments.

The CI hardware upgrade allows the MSD to produce high-quality, classical 

CI spectra, which include molecular adduct ions. A variety of reagent gases can 
be used. (See 

Chapter 6

, “Operating in CI Mode”” on 

page 143

.)

Figure 1.

5977B Series GC/MSD system, shown with an Agilent 8890 GC

ALS

8890 GC

Touchscreen

5977B Series 
MSD

MSD power switch

GC power switch

System status LED

Summary of Contents for 5977B CI MSD































































































































































































































































Reviews:

No comments

Related manuals for 5977B CI MSD

Gator Prime GP Series Installation, Operation, And Maintenance Manual With Parts List preview
GP Series
Brand: Gator Prime Pages: 32
IBO PSI Series Manual preview
PSI Series
Brand: IBO Pages: 22
vacuubrand NT Series Instructions For Use Manual preview
NT Series
Brand: vacuubrand Pages: 44
salmson NXT Installation And Starting Instructions preview
NXT
Brand: salmson Pages: 16
Underhill GULP PRO Care And Maintenance Instructions preview
GULP PRO
Brand: Underhill Pages: 2
T.I.P. I-COMPAC 7500 Manual preview
I-COMPAC 7500
Brand: T.I.P. Pages: 104
Nakayama PRO NP2015 Manual preview
PRO NP2015
Brand: Nakayama Pages: 29
ProMinent S3Cb Operating Instructions Manual preview
S3Cb
Brand: ProMinent Pages: 124
Warren rupp Sandpiper F10 Service & Operating Manual preview
Sandpiper F10
Brand: Warren rupp Pages: 16
Aquacal SunPower SP05 Installation Manual preview
SunPower SP05
Brand: Aquacal Pages: 108
REMKO KPS 130 Assembly And Operating Instructions Manual preview
KPS 130
Brand: REMKO Pages: 16
Carrier 38YZA024-30 Product Data preview
38YZA024-30
Brand: Carrier Pages: 28
Calpeda NGX Operating Instructions Manual preview
NGX
Brand: Calpeda Pages: 48
Graco Husky 307 F Series Instructions-Parts List Manual preview
Husky 307 F Series
Brand: Graco Pages: 36
Invertek Drives OPTIDRIVE ODP-2-22010-1HF42-SN Manual preview
OPTIDRIVE ODP-2-22010-1HF42-SN
Brand: Invertek Drives Pages: 72
Magic-Pro MHP-10-24 Installation And Maintenance Instructions Manual preview
MHP-10-24
Brand: Magic-Pro Pages: 15
CARVIN STARFALL User Manual preview
STARFALL
Brand: CARVIN Pages: 9
Sundez SDDC-050-B Installation Instructions Manual preview
SDDC-050-B
Brand: Sundez Pages: 24

Brands by name

Popular brands

Load more brands