manualshive.com logo in svg

Agilent Technologies 54621A, Service Manual

Share
Download
Agilent Technologies 54621A Service Manual Download Page 115

DECLARATION OF CONFORMITY

According to ISO/IEC Guide 22 and CEN/CENELEC EN 45014

Manufacturer’s Name:
Manufacturer’s Address:

Agilent Technologies, Inc.
Garden of the Gods Road
Colorado Springs, Colorado
80907  U.S.A.

Declares, that the product

Product Name:

Digitizing Oscilloscope

Model Number(s):

54621A/D, 54622A/D, and 54624A/AN

Product Option(s):

All options based on the above

Is in conformity with:

EMC:

IEC 61326-1:1997+A1:1998 / EN 61326-1:1997+A1:1998
CCISPR 11:1990/EN 55011:1991– Group 1 Class A

[1]

 

IEC 61000-4-2:1995+A1:1998 / EN 61000-4-2:1995 (ESD 4kV CD, 8kV AD)
IEC 61000-4-3:1995/EN 61000-4-3:1995 (3V/m 80% AM)
IEC 61000-4-4:1995/EN 61000-4-4:1995 (0.5kV line-line, 1kV line-earth)
IEC 61000-4-6:1996/EN 61000-4-6:1996 (3V 80% AM, power line)
Australia/New Zealand: AS/NZS 2064.1

Saftey

IEC 61010-1:1990+A1:1992+A2:1995 / EN 61010-1:1993+A2:1995
Canada: CSA C22.2 No. 1010.1:1992
USA: UL 3111-1:1994

Additional Information:

The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC 
(including 93/68/EEC) and carries the CE-marking accordingly (European Union).

[1]

The product was tested in a typical configuration with Agilent Technologies test systems.

Date: 01/27/2000

Name

Ken Wyatt / Product Regulations Manager

For further information, please contact your local Agilent Technologies sales office, agent or distributor.

service.book  Page i  Wednesday, December 18, 2002  8:35 AM

Summary of Contents for 54621A























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands