Agilent Technologies 53210A Options Installation Download

Page: 2 / 44

53210A/53220A/53230A

Option

Installation

53210A/53220A/53230A Option Installation

Introduction

The following information generally applies to all options.

Tools Required

The following tools are required for the installation procedures:

•

Hand TORX‚ 8 screwdriver (T8)

•

Hand TORX‚ 10 screwdriver (T10)

•

Hand TORX‚ 20 screwdriver (T20)

•

7- mm spintight or 9/32" manual nut driver (GPIB connector screws)

•

14- mm deep- socket or deep spintight (TypeN and BNC connectors)

•

1/4" spintight (Option 115 standoffs)

•

5/16" open- end wrench (SMA connectors)

•

Long- nose Pliers

•

3/16" or 1/4" wide medium slot screwdriver

Do This First

N O T E

Before performing any of the retrofit procedures turn the counter off and remove
ac line power from the rear ac line socket.

WA R N I N G

Hazardous Voltages exist on some internal circuits of the counter. After discon-
necting the AC line power cord, wait at least 6 minutes for the High-Voltage
capacitors to discharge before removing the cover.

C A U T I O N

ESD damage caused by customer access to the internal circuits of the counter
without proper ESD protection may void the instrument warranty.

Summary of Contents for 53210A













































Search results

Summary of Contents for 53210A

Reviews:

Related manuals for 53210A

Brands by name

Popular brands

Agilent Technologies 53210A, Options Installation

Search results

Summary of Contents for 53210A

Reviews:

Related manuals for 53210A

Brands by name

Popular brands