manualshive.com logo in svg

Agilent Technologies 53210A, Options Installation

Share
Download
Agilent Technologies 53210A Options Installation Download Page 31

53210A/53220A/53230A Option Installation

31

53210A/53220A/53230A Option Installation

53220A/53230A Channel 3 Front Panel Input (Options 106 and 202)

Option 106/202 Channel 3 Parts (53200U - 106)

Item

Agilent Part No.

Qty.

•

6.0 GHz PC Assembly

53200-67505

1

•

Ribbon Cable, 40-pin

53200-61605

1

•

Labels, 6 GHz 

53200-84301

2

•

Bracket, Aluminum

53200-00603

1

•

TORX 10 screws 

0515-0430

4

•

Screws, Flathead

0515-1946

2

•

TypeN-to-SMA Connector-Adapter

E4418-20009

1

•

RF Cable, Front, SMA Semi-rigid

53200-61612

1

•

Washer Plate (with "LIFT" tab)

E4418-00016

1

•

14mm Hex Nut

2950-0132

1

Preliminary Steps

1. Remove the cover and rear bezel as described under “

Removing the 

Cover and Rear Bezel

” at the beginning of this document.

2. If installed, temporarily move the Option 300 internal battery as 

described under “

Moving the Internal Battery (Option 300)

” at the 

beginning of this document.

3. Assemble the parts in the Option 106/115 package as follows (Figure 

18):

C A U T I O N

Before proceeding with the installation, follow all the ESD steps as outlined in the 
section titled "Do This First"at the beginning of this document.

Summary of Contents for 53210A













































Reviews:

No comments

Brands by name

Popular brands

Load more brands