manualshive.com logo in svg

Agilent Technologies 53210A, Options Installation

Share
Download
Agilent Technologies 53210A Options Installation Download Page 24

24

 53210A/53220A/53230A 

Option 

Installation

53210A/53220A/53230A Option Installation

16. Re- install the T20 TORX screw removed in step 6 above.

17. Re- install the P500 Processor board on the underside of the mother-

board (removed in steps 3 and 4 above) as follows (refer to Figure 11):

•

Insert  the  rear  left- hand  corner  of  the  PC  board  in  the  horizontal 
slot (as viewed from above) and then line up the edge connector pins 
on the PC board with the edge connector on the underside of the 
front panel.

•

Press in carefully on the rear edge of the PC board until the edge 
connector tabs lock into place.

•

Install the T10 TORX screw through the hole in the P500 board into 
the standoff on the A1 motherboard (screw removed in step 2).

18. Turn the chassis upright. Install the Option 106 Channel 2 assembly as 

follows:

19. Remove the T20 TORX screw at the rear of the motherboard.

20. Connect one end of the supplied 40- pin ribbon cable to J900 on the 

motherboard. Connect the other end to J401 on the underside of the 

Channel 2 assembly.

21. Set the Channel 2 assembly down on top of the motherboard so that 

the female SMA edge connector is near the male SMA connector of the 

semi- rigid cable installed on the front panel assembly (see Figure 15).

N O T E

Be sure that the right-hand side tab (see step 8 above) locks the side panel in 
place. It may be necessary to gently press outward on the right-hand side panel 
until the tab locks into place.

N O T E

Verify that the PC board is parallel horizontally with the motherboard. The rear 
left-hand corner must sit on top of the small standoff inside the slot.

Summary of Contents for 53210A













































Reviews:

No comments

Brands by name

Popular brands

Load more brands