manualshive.com logo in svg

Agilent Technologies 53210A, Options Installation

Share
Download
Agilent Technologies 53210A Options Installation Download Page 30

30

 53210A/53220A/53230A 

Option 

Installation

53210A/53220A/53230A Option Installation

7. Install the supplied SMA semi- rigid cable as follows:

•

Insert the end of the supplied semi- rigid cable with the female SMA 
connector through the hole on the rear panel marked "Opt 106/115". 

•

Line up the male SMA cable connector on the other end of the 
semi- rigid cable and the Channel 2 assembly SMA edge connector, 
connect them together and tighten the SMA cable connector using a 
5/16" wrench. 

•

Secure the rear panel SMA connector with the supplied 5/16" hex 
nut and lockwasher. Do not overtighten.

8. Re- install the Option 300 Internal Battery (if moved). Be sure to 

re- connect any disconnected cables.

9. Re - install the cover, rear bezel, and handle (if applicable).

10. Install the supplied Option 106 label above the rear panel SMA con-

nector in the location provided. 

N O T E

Be sure there is no stress on the semi-rigid cable.

Summary of Contents for 53210A













































Reviews:

No comments

Brands by name

Popular brands

Load more brands