Agilent Technologies 11713A Operating And Service Manual Download Page 83

Page: 83 / 88

8-20 11713A Operating and Service Manual

Servicing the Attenuator/Switch Driver

Troubleshooting the A6 Interface Assembly

The A6 interface assembly contains the GPIB address switch, the
connectors for the X and Y attenuators, and the wiring for switch
outputs 9 and 0.

To Troubleshoot the A6 Interface Assembly

1. To test the circuitry of the A6 interface assembly, check the driver

both in manual and remote operation.

a. Manually press the attenuator buttons several times. The light

should come on/off each time that a button is activated.

b. If the manual verification is satisfactory, check the

computer-controlled remote operation by sending these
commands.

2. If the response is satisfactory, the A6 interface assembly should be

operational.

3. If the response is unsatisfactory, refer to the troubleshooting

procedures for the A2 driver assembly.

Command

Desired Outcome

OUTPUT 728;”Al2345678”

All attenuator lights go on except the local light.

OUTPUT 728;”Bl2345678”

All attenuator lights go off except the remote light.

Summary of Contents for 11713A

























































































Search results

Summary of Contents for 11713A

Reviews:

Related manuals for 11713A

Brands by name

Popular brands

Agilent Technologies 11713A, Operating And Service Manual

Search results

Summary of Contents for 11713A

Reviews:

Related manuals for 11713A

Brands by name

Popular brands