manualshive.com logo in svg

AGFA D2RS, User Manual

Share
Download
AGFA D2RS User Manual Download Page 40

Digital Remote Controlled Table with dynamic flat panel detector 

 

 

 

User’s Manual

 

39 

 

4.4. SERVICE MESSAGES 

These messages appear at the bottom of touch screen of the 
main table control console 

They indicate the potential cause of a system failure. In general, 
the system forbids all the movements and messages are 
dedicated to Field Service. 

Then, if any of the messages below appears, turn the system 
OFF and ON; if the message remains, call Field Service 

 

Messages displayed on bottom of screen 

NO COMMUNICATION WITH THE TABLE 

ELEVATION EPS SUP MAX 

POTENTIOMETER 10V SUPPLY DEFAULT 

LONG TABLE TOP EPS SUP MAX 

DEFAUT AUTOMATE (TPU) 

S.I.D EPS SUP MAX 

ERR. FILE PARAM.CFG 

LAT TABLE TOP EPS SUP MAX 

ERR. FILE PRG.CFG 

TILTING POTENTIOMETER OUT OF RANGE 

ERR CMDE CARRIAGE 

TABLE HEIGHT POTENTIOMETER OUT OF RANGE 

ERR CMDE COLUMN 

LONG TABLE TOP POTENTIOMETER OUT OF RANGE 

ERR CMDE TILTING 

S.I.D. POTENTIOMETER OUT OF RANGE 

ERR CMDE TABLE HEIGHT 

LAT TABLE TOP POTENTIOMETER OUT OF RANGE 

ERR CMDE LONG TABLE  TOP 

CARRIAGE SLIPPING FAULT 

ERR CMDE S.I.D. 

COLUMN SLIPPING FAULT 

ERR CMDE LAT TABLE TOP 

TILTING SLIPPING FAULT 

ERR CMDE COMPRES ESCAMOT 

ELEVATION SLIPPING FAULT 

ERR CMDE COMPRES H/B 

LONG TABLE TOP SLIPPING FAULT 

CARRIAGE INVERTER DEFAULT 

S.I.D. SLIPPING FAULT 

COLUMN INVERTER DEFAULT 

LAT TABLE TOP SLIPPING FAULT 

TILTING INVERTER DEFAULT 

DEFAUT GLISSEMENT COMPRES ESCAMOT 

TABLE HEIGHT INVERTER DEFAULT 

DEFAUT GLISSEMENT COMPRES H/B 

LONG TABLE TOP INVERTER DEFAULT 

CODEUR CHARIOT HORS LIMITE LOG 

CARRIAGE ENCODER DEFAULT 

CODEUR INCIDENCE HORS LIMITE LOG 

COLUMN ENCODER DEFAULT 

POTAR BASCULT HORS LIMITE LOG 

TILTING POTENTIOMETER FAULT 

POTAR ELEVAT HORS LIMITE LOG 

TABLE HEIGHT POTENTIOMETER FAULT 

POTAR DOS LONG HORS LIMITE LOG 

LONG TABLE TOP POTENTIOMETER FAULT 

POTAR FOCALE HORS LIMITE LOG 

S.I.D. POTENTIOMETER FAULT 

POTAR DOS. LAT HORS LIMITE LOG 

LAT TABLE TOP POTENTIOMETER FAULT 

POTAR COMP.ESCAMOT HORS LIMITE LOG 

DEFAUT COM. TELECOMMANDE 

POTAR COMP.HB HORS LIMITE LOG 

CARRIAGE EPS SUP MAX 

RET. COMPRESSOR POTENTIOMETER OUT OF SOFT RANGE 

COLUMN EPS SUP MAX 

RET. COMPRESSOR STRAIN GAUGE FAULT 

TILTING EPS SUP MAX 

 

For version with removable detector 

Additional messages 

ERR CMDE SENSOR ROTATION 

POTAR ROT CAPT HORS PLAGE 

SENSOR ROTATION POTENTIOMETER FAULT 

SENSOR ROTATION SLIPPING FAULT 

SENSOR ROTATION EPS SUP MAX 

POTAR ROT CAPT HORS LIMITE LOG 

 

In all cases, follow the instructions given in the display. 

For any other messages, make a note of them and call the After-Sales Service of your reseller or the manufacturer. 

Summary of Contents for D2RS









































Reviews:

No comments

Brands by name

Popular brands

Load more brands