manualshive.com logo in svg

AGCO LELY ATTIS PT 130, Operator'S Manual

Share
Download
AGCO LELY ATTIS PT 130 Operator'S Manual Download Page 59

4 Maintenance and lubrication

4.1 Prepare the machine to do maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

61

4.2 Preventative maintenance schedule

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

63

4.3 Lubrication chart

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

64

4.4 Lubricate the machine

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

65

4.4.1 Lubricate the wrapping table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

4.4.2 Lubricate the gear wheels of the transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

4.4.3 Lubricate the drive chain of the wrapping table rollers . . . . . . . . . . . . . . . . . . . . . . . . . 67

4.5 Adjust the chain tension

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

69

4.6 Measure the oil pressure in the accumulator

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

71

4.7 Examine the hydraulic hoses for damage and leaks

. . . . . . . . . . . . . . . . . . . . . . . .

72

4.8 Replace the film knife

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

73

4.9 Clean the machine

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

75

4.10 Torque the nuts of the transport wheel

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

76

Table of contents

Bale Wrapper 

59

4820.LE.EN01

Summary of Contents for LELY ATTIS PT 130



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands