AGCO LELY ATTIS PT 130 Operator'S Manual Download Page 67

Page: 67 / 98

Apply Molykote BR2 plus grease to the

gearwheels.

GUID-325DB636-3EF1-48C5-9AE4-C82DC208F429-high.jpg [High]

Fig. 8

Install the cover plate on the gearbox.

Install the three bolts on the gearbox cover.

GUID-664AF55C-DC72-44BC-AE9D-18D615CEA2C1-high.jpg [High]

Fig. 9

4.4.3 Lubricate the drive chain of the wrapping table rollers

WARNING: Risk of injury

Put on the correct Personal Protective Equipment (PPE) when you use lubricants and oils.
Lubricants and oils are dangerous to health and the environment.

Procedure
1.

Remove the two bolts from the drive chain

housing.

GUID-F0791CD5-855D-46A3-9FAE-B28635F0C2CC-high.jpg [High]

Fig. 10

GUID-1B4AFAA1-7FDE-4DC2-B5D3-DF3327D11429 [V1]

4. Maintenance and lubrication

Bale Wrapper

4820.LE.EN01

Summary of Contents for LELY ATTIS PT 130


































































































Search results

Summary of Contents for LELY ATTIS PT 130

Reviews:

Brands by name

Popular brands

AGCO LELY ATTIS PT 130, Operator'S Manual

Search results

Summary of Contents for LELY ATTIS PT 130

Reviews:

Brands by name

Popular brands