background image

 

 

18 

5.  OPERATIONS 

 

DANGER

  

 
 

 WATCH FOR PEDESTRIAN 
TRAFFIC- Rollers will always win 
and pedestrians will lose the battle 
with a LandRoller.  
 

 

5.1.  EASIFOLD ( NOT 

POWERFOLD) FOLDING 
FROM ROAD TO FIELD. 

EasiFold is the standard Ag Shield configuration 
where each inner  wing wheel is rotated 25 
degrees by a hydraulic cylinder, and the operator 
must then 

back up the whole unit

 to have the 

wing move from behind the center section to the 
field position. This is different from the Ag Shield 
PowerFold option where the wheels are first 
turned a full 90 degree by the hydraulic cylinder, 
a drive spindle is lowered to contact the wheel,  
and then sequence valve will keep the cylinder 
pressure at the preset level, and 

drive the wings 

to field position while the LandRoller center 
frame is stationary

. LandRoller wheel rotate 

circuits 

are shipped with the large ½” hoses 

installed so that field installation of the PowerFold 
option is a simple bolt on attachment at the inner 
wheel location.  
 
There are 2 hydraulic circuits on all 5 section Ag 
Shield LandRollers: 

A. 

This first circuit hereafter on “Lever 1”  
that rotates the wheel assembly so that a 
backing up motion will move the 
LandRoller wings to field position, This is 
the same circuit that is the used for 
PowerFold wheel option. 

B.  The second circuit ( Lever2) that raises 

or lowers the center, inner, and outer 
wheels for road transport, and is teed 
together with the diagonal arm locking 
function, the hydraulic hitch locking 
cylinder,   

 

Unfolding to field Procedure 

1.  Chose a reasonably level location with no 

bystanders or small children in the vicinity.  

2.  Operate the whole unit in a forward direction 

until the wings are trailing out behind the 
center section at an equal and perpendicular 
angle to the center section. 

 

 

FIGURE 10 WINGS TRAILING DIRECTLY 
BEHIND 

3.  Operate Lever 2 to raise the rollers up ALL 

the Way to top to allow transport locks to be 
removed.  

4.  Set parking brake, place tractor transmission 

in Neutral, leave the tractor cab tractor, 

5.  Make one rotation around the machine 

doings all the road locks in sequence. Start 
with floating hitch left side, move the height 
lock from B to C, and then remove Pin A and 
place in holder nearby.  

 

 

FIGURE 11 FLOATING HITCH 2 POINTS EACH 
SIDE LOCKED 

Summary of Contents for LandRoller
























































Reviews: