Afore Anybuild BNT KTL Series User Manual Download Page 27

Page: 27 / 33

2.Please contact with local dealer if error remains the same after
several reset.

IntFaultG

1.Electricity grid abnormal
2.DCI too high

1.After electricity grid returns to normal, the mac

hine will

automatically restart.

2.Please contact with local dealer if error remains the same after
several reset.

IntFaultJ

Relay failure

Please contact with local dealer if error remains the same after
several reset.

IntFaultK

1.Electricity grid abnormal
2.Bus differential fault

1.After electricity grid returns to normal, the mac

hine will

automatically restart.

2.Please contact with local dealer if error remains the same after
several reset.

IntFaultL

1.Electricity grid abnormal
2.Low Bus voltage fault

1.After electricity grid returns to normal, the machine

will

automatically restart.

2.Please contact with local dealer if error remains the same after
several reset.

IntFaultM

1.Electricity grid abnormal
2.High Bus voltage fault

1.After electricity grid returns to normal, the machine will
automatically

restart.

2.Please contact with local dealer if error remains the same after
several reset.

IntFaultN

Internal hardware fault

Please contact with local dealer if error remains the same after
several reset.

IntProtectA

Offset current protection

Please contact with local dealer if error remains the same after
several reset.

IntProtectB

Relay protection

Please contact with local dealer if error remains the same after
several reset.

IntProtectC

Over current protection

Please contact with local dealer if error remains the same after
several reset.

IntProtectD

1.PV side high current
2.Boost over current protection

1.Adjust the panel configuration to lower the input current.
2.Please contact with local dealer if error remains the same after
several reset.

IntProtectE

1.Electricity grid abnormal
2.Soft start overtime protection

1.After electricity grid returns to normal, the mac

hine will

automatically restart.

2.Please contact with local dealer if error remains the same after
several reset.

IntProtectF

When direct current is at low
voltage, Soft start overtime
protection

Please contact with local dealer if error remains the same after
several reset.

IntProtectG

Bus voltage differential protection Please contact with local dealer if error remains the same after

several reset.

IntProtectH

Low Bus voltage protection

Please contact with local dealer if error remains the same after
several reset.

IntProtectI

High Bus voltage protection

Please contact with local dealer if error remains the same after
several reset.

IntProtectJ

Inverter bridge protection

Please contact with local dealer if error remains the same after
several reset.

IntProtectK

Bus hardware overvoltage

Please contact with local dealer if error remains the same after

Summary of Contents for Anybuild BNT KTL Series


































Search results

Summary of Contents for Anybuild BNT KTL Series

Reviews:

Related manuals for Anybuild BNT KTL Series

Brands by name

Popular brands

Afore Anybuild BNT KTL Series, User Manual

Search results

Summary of Contents for Anybuild BNT KTL Series

Reviews:

Related manuals for Anybuild BNT KTL Series

Brands by name

Popular brands