INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE
YOU
BEGIN
CONDITIONING
GUIDELINES
TROUBLESHOOTING
&
MAINTENANCE
LIMITED
W
ARRANTY
INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE YOU
BEGIN
CONDITIONING GUIDELINES
TROUBLESHOOTING &
MAINTENANCE
LIMITED WARRANTY
TOOLS INCLUDED
PARTS INCLUDED
1 Bayonet
1 Bicep Curl Bar
1 Seat Back Pad
1 Base Frame
1 Left Support Frame
1 Right Support Frame
1 Seat Back Adjustment Bar
1 Radial Arm Assembly
1 Exercise Flipbook
2 Seat Adjustment Pins
1 Leg Roller Support Tube
1 Water Bottle Holder
1 Seat Bottom Adjustment Bar
1 Center Support Frame
1 Seat Weldment
2 Weight Shrouds
2 Guide Rods
1 Weight Selection Pin
1 5 lb. Increment Weight
1 Dual Floating Pulley Bracket
1 Set Of Weight Plate Decals
1 Center Connection Tube
1 Lower Connection Tube
1 Lower Pulley Bracket
2 Upgrade Spacers
2 Accent Pieces
2 Single Floating Pulley Bracket
1 Upper Pulley Assembly
1 Seat Bottom Pad
1 Nylon Ankle Strap
2 Handles
1 Lat Pulldown Bar
10 Hardware Bags
2 Foam Rollers
1 Seat Head Pad
2 Side Connection Tubes
1 Upper Mounting Bracket
1 Lower Mounting Bracket
LAT PULLDOWN BAR
WATER BOTTLE HOLDER
CENTER SUPPORT FRAME
LARGE “O” RING
LEFT SUPPORT FRAME
CABLE “B”
RADIAL ARM ADJUSTMENT PIN
SEAT BACK PAD
HANDLES
SEAT BACK ADJUSTMENT KNOB
BICEP CURL BAR
SEAT HEAD PAD
SEAT BOTTOM PAD
SEAT WELDMENT
LEG EXTENSION/CURL DOWN TUBE
SEAT HEIGHT ADJUSTMENT KNOB
ADJUSTMENT BAR
FOAM ROLLERS
ADJUSTABLE FOOTPLATE
CABLE “D”
BASE FRAME
SEAT ASSEMBLY SAFETY PIN
RIGHT SUPPORT FRAME
SINGLE FLOATING PULLEY BRACKET
WEIGHT SELECTION PIN
WEIGHT SHROUD
CABLE “C”
DUAL FLOATING PULLEY BRACKET
GUIDE ROD
BAYONET
ACCENT PIECE
UPPER PULLEY ASSEMBLY
RADIAL ARM ASSEMBLY
CABLE “A”
If you have questions or if there are any missing parts, contact Customer Tech Support.
Contact information is located on the back panel of this manual.
For a complete exploded diagram, visit us at www.advancedfitnessgroup.com
19 mm Flat Wrench
13 mm/17 mm Flat Wrench
4 mm Allen Wrench
5 mm Allen Wrench
6 mm Allen Wrench
NOTE:
During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt.
NOTE:
A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike
grease is recommended.
PRE-ASSEMBLY
ASSEMBLY
STEP 1
BASE FRAME
ARC WASHER (D)
NYLON NUT (E)
NYLON NUT (E)
LEFT SUPPORT FRAME
CENTER
SUPPORT FRAME
RIGHT SUPPORT FRAME
BOLT (A)
BOLT (B)
FLAT
WASHER (C)
ARC WASHER (D)
FLAT WASHER (C)
LOWER PULLEY BRACKET
Place
BASE FRAME
on floor in desired
location.
Open
HARDWARE BAG
1
.
Attach
RIGHT
SUPPORT FRAME
to
right side of
BASE
FRAME
using 2
BOLTS
(B),
4
ARC
WASHERS
(D)
and 2
NYLON NUTS
(E)
.
Attach
LEFT SUPPORT
FRAME
to left side of
BASE FRAME
using
2
BOLTS (B),
4
ARC
WASHERS (D)
and 2
NYLON NUTS (E)
.
Attach
CENTER
SUPPORT FRAME
and
LOWER
PULLEY
BRACKET
to
BASE
FRAME
using 2
BOLTS
(A),
4
FLAT
WASHERS
(C)
and 2
NYLON NUTS
(E)
.
NOTE:
Ensure that
the
LOWER PULLEY
BRACKET
is positioned
as shown in diagram.
A
B
C
D
E
NYLON
NUT (E)
Qty: 6
FLAT WASHER (C)
Qty: 4
ARC WASHER (D)
Qty: 8
BOLT (A)
75 mm
Qty: 2
BOLT (B)
95 mm
Qty: 4
HARDWARE BAG 1 CONTENTS :
2.0AS_Rev.1.5.indd 6-7
9/23/08 10:14:12 AM
