INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE
YOU
BEGIN
CONDITIONING
GUIDELINES
TROUBLESHOOTING
&
MAINTENANCE
LIMITED
W
ARRANTY
INTRODUCTION
IMPORT
ANT
PRECAUTIONS
ASSEMBL
Y
BEFORE YOU
BEGIN
CONDITIONING GUIDELINES
TROUBLESHOOTING &
MAINTENANCE
LIMITED WARRANTY
ASSEMBLY
STEP 2
NYLON
NUT (E)
Qty: 6
LARGE “O” RING
Qty: 1
ARC WASHER (D)
Qty: 12
BOLT (B)
95 mm
Qty: 4
BOLT (F)
90 mm
Qty: 2
HARDWARE BAG 2 CONTENTS :
RIGHT
SUPPORT
FRAME
CENTER
SUPPORT FRAME
LARGE
“O” RING
NYLON NUT (E)
LEFT SUPPORT
FRAME
UPPER PULLEY
ASSEMBLY
ARC WASHER (D)
BOLT (A)
ARC WASHER (D)
BOLT (F)
ARC WASHER (D)
SEAT
WELDMENT SET
SEAT
ADJUSTMENT
PIN
SEAT SAFETY PIN
NUT (E)
ASSEMBLY
STEP
NYLON
NUT (E)
Qty: 2
NYLON
NUT (K)
Qty: 1
FLAT
WASHER (C)
Qty: 10
BOLT (F)
25 mm
Qty: 2
BOLT (G)
92 mm
Qty: 1
FLAT
WASHER (I)
Qty: 2
BOLT (H)
20 mm
Qty: 4
BOLT (J)
83 mm
Qty: 2
LOCK
WASHER (L)
Qty: 2
HARDWARE BAG CONTENTS :
BOLT (G)
BOLT (J)
BOLT (J)
LEG ROLLER
SUPPORT TUBE
LOWER
CONNECTION TUBE
FLAT WASHER (I)
FLAT WASHER (C)
NYLON NUT (E)
NYLON NUT (K)
FLAT
WASHER (C)
LOCK
WASHER (L)
RADIAL ARM
ASSEMBLY
NYLON NUT (E)
CENTER
CONNECTION
TUBE
LEFT
CONNECTION
TUBE
CENTER
SUPPORT
FRAME
RIGHT CONNECTION TUBE
BOLT (H)
FLAT WASHERS (C)
BOLT (F)
Open
HARDWARE BAG 2
.
Slide
LARGE “O” RING
onto
CENTER SUPPORT
FRAME
as shown in
diagram.
Attach
UPPER PULLEY
ASSEMBLY
to
CENTER
SUPPORT FRAME
using
4
BOLTS (F)
and 4
ARC
WASHERS (D)
and 2
NYLON NUTS (E)
. Tighten
this hardware.
Attach
UPPER PULLEY
ASSEMBLY
to
RIGHT
MAIN SUPPORT FRAME
using 2
BOLTS (B)
, 4
ARC WASHERS (D)
and 2
NYLON NUTS (E)
.
Attach
UPPER PULLEY
ASSEMBLY
to
LEFT
SUPPORT FRAME
using
2
BOLTS (B)
, 4
ARC
WASHERS (D)
, and 2
NYLON NUTS (E)
.
Install
SEAT WELDMENT
SET
onto posts on
CENTER SUPPORT FRAME
as shown in diagram, and
insert
SEAT SAFETY PIN.
Install
SEAT ADjUSTMENT
PIN
into
SEAT WELDMENT
SET
as shown in
diagram. (Fully thread
into
SEAT WELDMENT
SET
after
SEAT BOTTOM
ADjUSTMENT BAR
is
installed.)
A
B
C
D
E
F
G
Open
HARDWARE BAG
.
Remove
STOPPER
from front side of
RADIAL ARM ASSEMBLY
and reinstall on back side.
Tighten both
STOPPERS
.
Attach
RADIAL ARM ASSEMBLY
to
CENTER SUPPORT FRAME
using 2
BOLTS (F),
2
LOCK
WASHERS (L)
and
2
FLAT WASHERS (C).
Tighten this hardware.
Attach
RIGHT SIDE CONNECTION TUBE
to
SEAT WELDMENT SET
and to
LOWER
CONNECTION TUBE
using 2
BOLTS (H)
and 2
FLAT WASHERS (C)
, as shown in diagram.
Repeat on left side.
Attach
CENTER CONNECTION TUBE
to
SEAT WELDMENT SET
and to
LOWER CONNECTION
TUBE
using 2
BOLTS (j)
, 4
FLAT WASHERS (C)
and 2
NYLON NUTS (E)
.
Attach
LEG ROLLER SUPPORT TUBE
to
LOWER CONNECTION TUBE
using 1
BOLT (G)
, 2
FLAT WASHERS
(I)
and 1
NYLON NUT (K)
. Tighten all hardware in Step 3.
A
B
C
D
E
F
G
RADIAL ARM ASSEMBLY
STOPPER
STEP -B: INSTALLING THE STOPPER:
2.0AS_Rev.1.5.indd 8-9
9/23/08 10:14:19 AM
