background image

 

Page 19

 

 

Warranty 

General Terms: 

 

aFe warrants their products to be free from manufacturer’s defects due to workmanship and material. 

  This warranty applies only to the original purchaser of the product and is non-transferrable. 

  Proof of purchase of the aFe product is required for all warranty claims. 

  Warranty is valid provided aFe instructions for installation and/or cleaning were properly followed. 

  Proper maintenance with regular inspections of product is required to insure warranty coverage. 

  Damage due to improper installation, abuse, unauthorized repair or alteration is not warranted. 

  Incidental or consequential damages or cost, including installation and removal of part, incurred due to failure of aFe product is not 

covered under this warranty. 

  All warranty is limited to the repair and/or replacement of the aFe part. To request Return Goods Authorization 

(“RGA”), email 

[email protected] or call (951)493-7100. Upon receipt of the RGA, you must return the product to the address provided in the 
RGA, freight prepaid and accompanied with a dated proof of purchase and the RGA. Upon receipt of the defective product and 
upon verification of proof of purchase, aFe will either repair or replace the defective product within a reasonable time, not to exceed 
thirty days. 

Product Category 

 

 

 

 

P/N Prefix 

 

 

 

 

Warranty duration 

Direct OE Replacement Filters 

 

 

 

10, 11, 30, 31, 71, 73 

 

 

 

Life of the vehicle 

Racing Filters   

 

 

 

 

18 

 

 

 

 

 

1 year 

Universal 

 

 

 

 

 

20, 21, 23, 24, 72, TF 

 

 

 

2 years 

Air Intake Systems 

 

 

 

 

50, 51, 53, 54, 55, 56, 57, 58, 75, TR, TA, TL, TM  2 years 

Exhaust Systems 

 

 

 

 

49 

 

 

 

 

 

2 years 

Intercoolers & Intercooler Tubes   

 

 

46-2 

 

 

 

 

 

2 years 

Intake Manifolds  

 

 

 

 

46-1 

 

 

 

 

 

2 years 

Differential Cover 

 

 

 

 

46-7 

 

 

 

 

 

Life of the vehicle 

Exhaust Manifolds 

 

 

 

 

46 

 

 

 

 

 

2 years 

Throttle Body Spacers   

 

 

 

46-3 

 

 

 

 

 

2 years 

Turbochargers   

 

 

 

 

46-6 

 

 

 

 

 

2 years* 

Fluid Filters 

 

 

 

 

 

44 

 

 

 

 

 

90 days 

Pre-Filters 

 

 

 

 

 

28 

 

 

 

 

 

2 years 

Heavy Duty OE Replacement 

 

 

 

70 

 

 

 

 

 

2 years 

PowerSports OE Replacement   

 

 

81, 87   

 

 

 

 

2 years 

PowerSports Intake Systems 

 

 

 

85 

 

 

 

 

 

2 years 

No other warranty expressed or implied applies nor is any person or advanced FLOW engineering authorized to assume any other 
warranty. Some States do not allow the exclusion or limitation of incidental or consequential damages or do not allow limitations on how 
long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, 
and you may also have other rights which vary from State to State. 

*See turbocharger warranty for more info

Summary of Contents for 52-10002D





















Reviews: