manualshive.com logo in svg

Afag 50076883, Manual, Page: 29 / 44

Share
Download
Afag 50076883 Manual Download Page 29

                                                                                                                      

 

29                                                                   PS 25-32-OI-vers.3.5 gb. 21.07.14.docx 

 

 

 

 

 

 

 

Mounting ZA on the PS module 

(effective for the extension stroke) 

The ZA is mounted in an intermediate position for an extension stroke and is fine 
adjusted by adjusting the shock absorber and the stop screw (range of adjustment: PS 
25 / 32 (20 mm)) 

1 

ZAs can be fitted for module strokes from 100 mm onward (1x for the extension 
stroke and 1x for the retraction stroke). The stopper angle plate can be mounted at 
the front or rear base body plate, please ensure, however, that the intermediate 
stop bounds in the direction of the base body.                                                                
   

                                               

 

 

  

2 

 

                                                            

 

 

 

 

 

 

 

 

 

Cylinder                    Catch 

ZA-Housing    Fastening screw 

Base body 

Typ:    

 

ZA-PS 25 

ZA-PS 32

 

Order No. 

 

50222737 

50222738 

Weight of module: 

0,9 kg   

1,4 kg 

Operating Pressure:  4-8 bar  

4-8 bar 

Air connect 

: 

M5 

 

M5 

Damping traverse: 

Hydr.   

Hydr. 

 

Included in the delivery scope: 

ZA module with fastening screws 

Stopper angle plate with shock absorber, stop 
screw and fastening screws 

Example: ZA 
25 

Example: ZA 25 

Summary of Contents for 50076883













































Reviews:

No comments