background image

20 | 

P a g e

FCC warning

This device complies with part 15 of the FCC rules. Operation is subject to the 

following two conditions: (1) this device may not cause harmful interference, and (2) 

this device must accept any inte rference received, including interference that may 

cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a 

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against harmful interference in a 

residential installation. This equipment generates uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, 

may cause harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation. If this equipment 

does cause harmful interferenceto radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to 

correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and receiver.

•  Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement 

This equipment complies with FCC radiation exposure limits set forth for an 

uncontrolled environment. This equipment should be installed and operated with 

minimum distance 20cm between the radiator and your body.

Summary of Contents for PRIME6-PROX-IMPK-PE-4GA

















Reviews: