Aereco DXA 230 EXCELLENCE MB Installation And Maintenance Instruction Download

Page: 7 / 56

7 / 56

TF7128_A_NOT_INST_DXR230_EXC_MB

Aereco S.A.

2.3. DXR ASSEMBLING

When delivered, the DXR unit is furnished with 4 spigots with 4 screws each.

Those 4 spigots have to be screwed and sealed to the DXR unit as indicated on the

scheme.

The seal can be made thanks to silicone seal.

Assembling of the DXR spigots

Following the seal applied on the DXR Unit, a drying time

has to be taken into account before the operability of the

DXR.

DX Hub – Distribution box for demand

controlled supply airflows

·DX Hub 5 : 5 outlets in DN100 + 1 outlet for

balanced airflows in DN125

·DX Hub 6 : 6 outlets in DN75. Outlets n°5

and n°6 are dedicated to living room airflows
only and modulate both at the same time
according to the living room electronic
sensor.

·Envelope in galvanised steel.
·Dampers for supply airflows, driven by

sensors (Presence or CO

) for each room.

·Damper for balanced airflows (specific to DX

Hub 5)

The distribution box (DX Hub) coupled to the
exhaust compensation valve enables the
balance between supply and exhaust airflows.

Dimensions of DX Hub 6x75 mm

Dimensions of DX Hub 8x75 mm

Dimensions of DX Hub 6x100 mm

642

546

198

109

135

DN100

81,5

135

DN100

433

150,5

DN160

479,5

468

542

370

774

198

693

342

99,5

DN160

684

109

105

117,5

DN75

636

728,5

636

105

DN75

179,5

106

300

689
769

433

724,5

441

150

DN160

240

186

479

Summary of Contents for DXA 230 EXCELLENCE MB

























































Search results

Summary of Contents for DXA 230 EXCELLENCE MB

Reviews:

Related manuals for DXA 230 EXCELLENCE MB

Brands by name

Popular brands

Aereco DXA 230 EXCELLENCE MB, Installation And Maintenance Instruction

Search results

Summary of Contents for DXA 230 EXCELLENCE MB

Reviews:

Related manuals for DXA 230 EXCELLENCE MB

Brands by name

Popular brands