manualshive.com logo in svg

AEQ FORUM LITE, User Manual, Page: 38 / 135

Share
Download
AEQ FORUM LITE User Manual Download Page 38

 

 

AEQ

 

FORUM

 LITE

 

Ultra-compact digital audio mixer 

 

38 

NOTE 1:

 in order to activate this function you must purchase a user license. 

 

NOTE  2:

 

MADI

  functionality  is  not  compatible  with 

AoIP

  (audio  over  IP)  functionality,  both 

options can’t be active at the same time. 

 
 

2.2.4.2. Telephone hybrid optional module.  

 

 
At  the  back  panel  of  AEQ  FORUM  LITE,  integrated  double  digital  telephone  hybrid  module 
connectors  can  be  found,  labelled  as  "

HYBRID-1

"  and  "

HYBRID-2

".  This  interface  is  not 

equipped  by  default  unless  option  "

CA33:  DOUBLE  DIGITAL  TELEPHONE  HYBRID 

MODULE

" has been purchased. 

 
If you acquire this option later on, simple instructions will be enclosed with the module, allowing 
easy installation by any person with minimal experience in handling of electronic equipment or 
computers. 
 
Hybrid  module  has  enough  capacity  to  handle  two  independent  phone  lines.  It  has  two  RJ11 
connectors,  labelled  "

LINE

"  to  connect  the  physical  phone  lines,  and  two  more,  labelled  as 

"

SET

"  for  loop  connections  to  both  external  telephone  terminals  where  dialing  actions  will  be 

performed. 

 

 

RJ11 connector 

 
Control  and  configuration  of  the  signals  present  in  this  module  are  performed  using  the 
configuration  software.  For  more  information,  please  refer  to  section  "4.2.  Hardware 
Configuration menu" of this manual.

 

 
If  this  option  is  not  purchased  and  external  compatible  communication  devices  are  used,  you 
can control them using the programmable key section of AEQ FORUM LITE control surface. For 
more information, please refer to section "4.3.2.4. Configuration of Codec programmable keys" 
of this manual. 

 

 

2.2.5. Wiring. 

 
All  wiring  kits  described  below  are  optional  and  have  been  designed  by  AEQ  to  simplify  the 
installation of the unit. To facilitate the quick connection of the console in almost any installation, 
AEQ  can  supply  audio  and  data  cables  with  the  corresponding  DB-type  connectors  that  are 
used  to  connect  the  unit.  These  cables  can  be  cut  to  desired  lengths  and  soldered  on  patch 
panels,  punched  into  connector  strips  or  fitted  with  the  corresponding  connectors  to  be  used 
directly connected to the peripheral equipment. 
 
For easiest installation, FORUM LITE console uses a single type of Multiconnector: 

female DB 

15

, so only two types of cable are required: data and audio. Their description (for the maximal 

configuration) is: 

 

•

 

FR CAB INP: 

Male DB15 connector connected to a balanced and shielded four pair, 6-

meter cable with open-end termination, for 4 audio inputs or outputs. Max 9 cables per 
console.  

Summary of Contents for FORUM LITE








































































































































Reviews:

No comments