manualshive.com logo in svg

AEMC instruments 1015, User Manual

Share
Download
AEMC instruments 1015 User Manual Download Page 21

Megohmmeter Model 1015 

21 

WARNING: 

Make sure that no terminals are connected and that 

the switch is in the 

OFF

 position before opening the back of the 

instrument. 

•  Remove the yellow shockproof housing.
•  Remove the two screws from the back of the instrument (Figure 11).
•  Remove the back cover.
•  Replace the fuse or batteries.

NOTE: 

The instrument will operate correctly with a battery voltage 

range of (4.5 to 6.5) V.

•  Reverse the above procedure to install the back cover and the shock proof 

housing.

• 

To close the back stand flush with the back cover, apply light pressure at 

Point A in Figure 11.

Figure 11

5.2 CLEANING

WARNING: 

Before cleaning, disconnect all inputs to prevent 

possible electric shock.

The instrument should be cleaned periodically to keep the LCD clear and 

prevent the buildup of dirt and grease around the instrument’s buttons.

 



Clean the body of the instrument with a damp and soapy cloth

 



Do not submerge the instrument in water

 



Do not use solvents

+

+

+

+

Cover screws

1.5 V batteries LR6

1.6 A fuse

Point A

Summary of Contents for 1015

























Reviews:

No comments

Brands by name

Popular brands

Load more brands