AEM Dryflow Installation Instructions And Technical Manual Download Page 4 | Manualshive

Page: 4 / 13

background image

4

c. Loosen the hose clamp at the air box.

d. Remove bolt. Release the breather hose from the
valve cover.

e. Loosen the hose clamp at the throttle body.

f. Gently pull the inlet air temperature (IAT) sensor from
the inlet pipe. Remove the upper air box from the
vehicle.

NOTE: Do not pull by wires.

«
...
2
3
4
5
6
...
»

Summary of Contents for Dryflow














Reviews:

No comments

Related manuals for Dryflow

FDC/aerofilter STC SR00180SE

Brand: Intec Pages: 10

Brand: Hydrotech Pages: 20

StreamMax Classic 2000

Brand: Oase Pages: 20

Brand: Envirovent Pages: 16

Brand: Clarke Pages: 8

Mini Hobby RO 81050

Brand: CDL Pages: 2

tyco TY-L Series

Brand: Johnson Controls Pages: 6

Brand: TMC Aquarium Pages: 44

VIP4Tools Coaxial

Brand: DROPSA Pages: 11

Brand: Viking Pages: 6

Brand: Aquaporin Pages: 28

Brand: Allfyll Pages: 12

Brand: Parker Zander Pages: 72

Brand: Legend Pages: 3

Brand: MP Pages: 4

Brand: Watts Pages: 18

Brand: T.I.P. Pages: 52

WATER.IO Smart Water Bottle

Brand: Aqualife Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands