AEG OKO-LAVAMAT 86760 Page 46 User Manual Download

Page: 46 / 60

Installation and connection instructions

Installation of the appliance

Washing machines with curved panels are not suitable for installing
under units.

Transporting the appliance

•

Do not place the washing machine on its front or on its right side
(viewed from the front). Otherwise, electrical components can get
wet.

•

Never transport the unit without the transport safeguard. Do not re-
move the transport safeguard until the appliance is at the installation
location. Transporting the unit without the transport safeguard can
damage it.

•

Lift the appliance neither by an open filling door nor by the base.

When transporting the unit with a sack trolley:

•

Attach the sack trolley only at the side. The sack trolley shovel must
not be longer than 24 cm, otherwise the float switch can be de-
stroyed.

Remove transport packaging

Important!

It is essential to re-

move the transport packaging be-
fore putting the appliance into
operation. Keep all parts of the
transport packaging in a safe
place for future use.

Open both hose holders on the
appliance's rear side and remove
the hoses and mains cable.

Summary of Contents for OKO-LAVAMAT 86760





























































Search results

Summary of Contents for OKO-LAVAMAT 86760

Reviews:

Related manuals for OKO-LAVAMAT 86760

Brands by name

Popular brands

AEG OKO-LAVAMAT 86760, User Manual

Search results

Summary of Contents for OKO-LAVAMAT 86760

Reviews:

Related manuals for OKO-LAVAMAT 86760

Brands by name

Popular brands