background image

4. TECHNICAL DATA

Dimension

Width/ Height/ Total depth

59,7 cm /84,7 cm /66,0 cm

Electrical connection

Voltage

Overall power

Fuse

Frequency

230 V

2200 W

10 A

50 Hz

Level of protection against ingress of solid particles and

moisture ensured by the protective cover, except where

the low voltage equipment has no protection against mois‐

ture

IPX4

Water supply pressure

Minimum

Maximum

0.5 bar (0.05 MPa)

10 bar (1.0 MPa)

Water supply 

1)

Cold water

Maximum Load

Cotton

10 kg

Spin Speed

Maximum spin speed

1351 rpm

1) Connect the water inlet hose to a water tap with a 3/4'' thread.

5. INSTALLATION

WARNING!

Refer to Safety chapters.

5.1 Unpacking

1. Open the door. Remove all the items

from the drum.

Accessories delivered

with the appliance may

vary depending on the

model.

2. Put the packaging element on the

floor behind the appliance and

carefully put it down onto its rear

side. Remove the polystyrene

protection from the bottom.

1

2

CAUTION!

Do not lay washing machine

on its front.

3. Put the appliance back into an

upright position. Remove the power

supply cable and the drain hose from

the hose holders.

www.aeg.com

8

Summary of Contents for LR63R142













































Reviews: