background image

1

2

3

4

1

Burner cap

2

Burner crown

3

Ignition candle

4

Thermocouple

WARNING!

Do not keep the control knob pushed for more than 15 seconds.

If the burner does not light after 15 seconds, release the control knob, turn it into off posi-

tion and try to light the burner again after minimum 1 minute.

In the absence of electricity you can ignite the burner without electrical device; in this case

approach the burner with a flame, push the relevant knob down and turn it counter

-

clock-

wise to maximum gas release position.

If the burner accidentally goes out, turn the control knob to the off position and try to light

the burner again after minimum 1 minute.

The spark generator can start automatically when you switch on the mains, after installa-

tion or a power cut. It is normal.

Turning the burner off

To put the flame out, turn the knob to the symbol   .

WARNING!

Always turn the flame down or switch it off before you remove the pans of the burner.

Using the Wok Stand

A wok stand lets you to use a rounded bottom wok on the hob. Do not use the wok stand

with any other type of wok or pan. You must only use the wok stand on the Triple Crown.

When you install the wok stand, make sure that the recesses in the frame fit on the bars of

the pan supports.

14

Operation

Summary of Contents for HG755440SM

























Reviews: