manualshive.com logo in svg

AEG FAVORIT 50863, Instruction Book, Page: 44 / 48

Share
Download
AEG FAVORIT 50863 Instruction Book Download Page 44

Installation instructions

44

Electrical connection

Information concerning the electrical connection is given on the
rating plate on the edge of the dishwasher’s door.

Before plugging the appliance into the wall socket, make sure that:

1.

The mains voltage and current rating at the site of installation 
match the nominal voltage and current rating given on the rating 
plate. 

2.

The meter, fuses, mains power supply and wall socket can all take 
the maximum load required. Make sure that the socket and plug are 
compatible without having to use any type of adaptor. If necessary, 
have the domestic wiring system socket replaced.

To isolate the dishwasher from mains, remove the mains plug.

Important!
The plug must still be accessible after the appliance has been
installed.
In case that the electrical cable has to be replaced, please contact
your local Service Force Centre.
The appliance should not be connected to the electrical supply by
means of an extension cable.
Safety standards require the appliance to be earthed.
The manufacturer accepts no liability for failure to observe the
above safety precautions.

117998 91/0  21-04-2006  14:46  Pagina 44

Summary of Contents for FAVORIT 50863

















































Reviews:

No comments