background image

9

Dishwasher

Place grease filters in dishwasher. Select the most powerful

washing programme and highest temperature, at least 65°C.

Repeat the process. Refit the grease filters when they are dry.

When washing the metal grease filter in the dishwasher a slight

discolouration of the filter can occur, this does not have any impact

on its performance.

• Clean the inner housing using a hot detergent solution only

(never use corrosive, abrasive or flammable cleaning

products).

Charcoal filter

• The charcoal filter should only be used if you want to use the hood

in its filtering function.

• To do this you will need an original AEG  charcoal filter.

•

Replacing the charcoal filter

The charcoal filters cannot be cleaned, we recommend that they

should be replaced approximately every three months or more often

if the hood is used for more than three hours per day.

•

Mounting

Fit the charcoal filter first in the upper hooks then lock in position

using tabs 

E

Fig. 7

.

•

Removing

Push both tabs 

E

 and pull the charcoal filter downwards to extract it.

Fig. 7

.

• Always specify the hood model code number and serial number

when ordering replacement filters. This information is shown on the

rating plate located on the inside of the appliance.

• The  charcoal filter can be ordered from your local AEG Service

Force Centre.

Fig. 4

E

E

E

Fig. 7

Summary of Contents for CHDE 3160





















Reviews: