69
ENGLISH
Further Settings with the Multi Control Knob
Press and hold the multi control knob (21) to access
further setting options. Each further pressing of the
multi-controller switches to the next set point.
Turn the multi control knob to change the displayed
setting.
The following settings are possible:
BEEP
Key tone:
BEEP 2ND:
■
The unit sounds a beep tone
when you press and hold a multifunctional
button.
BEEP ALL:
■
The unit sounds a beep tone
every time you press a button.
BEEP OFF:
■
The unit sounds no beep tone.
AREA
Region, when the unit is used.
Europe (
EUR
) or
USA
NOTE
Changing this setting deletes all station
►
presets.
TA
Traffic announcements
TA SEEK:
■
With activated TA function the
unit searches for a station with traffic an-
nouncements.
TA ALARM:
■
No automatic station search.
The unit sounds a beep tone if no traffic
information is received and
NO TP/TA
is dis
-
played.
SEEK PI
is displayed if the selected
station does not transmit an RDS signal.
PI
Moving into an area where two stations
with identical AF, but different Pl code (PI =
program information) are received destabilizes
reception. In this situation you have two op-
tions:
PI SOUND:
■
To change stations the other
station is played for less than one second.
PI MUTE:
■
The other station is muted.
RETUNE
Delay for automatic search with traffic an-
nouncements and/or program information:
S
■
(Short) after approx. 30 seconds
L
■
(Long) after approx. 90 seconds
MASK
Setting to mask station during search:
DPI:
■
Alternative frequencies with different
Pl code are excluded from the search.
ALL:
■
Alternative frequencies with different
Pl code and no RDS information with high
signal level are excluded from the search.
Loudness Function
Press and hold
BAND/LOU/ENT
(2) to activate the
Loudness function.
LOUD ON
is displayed. The Loud-
ness function enhances the bass frequencies.
Press and hold
BAND/LOU/ENT
(2) again to deactivate
the Loudness function.
LOUD OFF
is displayed.
Sound Settings
Repeatedly press
EQ/TA
(19) to cycle through the
settings
FLAT
,
CLASSIC
,
POP
,
ROCK
or
EQ OFF
. The
selected setting is displayed.
Display Information
Repeatedly press
DISP
(14) to cycle through the following
display information:
Time (is automatically set if RDS reception is enabled),
radio station, programme type, frequency of the currently
set radio station, information on file names (only during
playback of a MP3 or WMA file).
NOTE
If no information is available
►
NO CLOCK
or
NO PTY
is
displayed.
If the information is too long for the display, it is
►
displayed as scrolling text.
Setting the time manually (in Radio Mode)
If the time should not be set automatically, proceed as
follows:
Press the button
DISP
(14) for a short while until the
time appears on the display.
Now keep the button
DISP
pressed until the minutes
flash.
Turn the multi-controller (21) to make the setting.
Press the button
DISP
for a short while. The hours start
flashing.
Turn the multi-controller (21) to make the setting.
Reset Radio
To reset the unit to default settings press
RESET
(25) with
a pointed object, i.e. pen.
Reset the unit when:
using it the first time after all cabling is done,
malfunctions of buttons occur,
error messages are displayed.
Radio Functions
Set RADIO Mode
Repeatedly press
MODE
(20) until frequency and band
are displayed.
Select Frequency Band
Press
BAND/LOU/ENT
(2) to toggle between FM1, FM2,
FM3 and AM. The selected frequency band is displayed.
Auto Search
Press
(15) or (16) to start auto search,
SEARCH
is
displayed. Search stops if a station is found.
Manual Search
Press and hold
(15) or (16) until
MANUAL
is
displayed.
Summary of Contents for AR 4020
Page 89: ......
