AEG ACM 9 Manual Download | Manualshive

Page: 50 / 51

background image

Manual ACM 9 - ARE i9 release

Version: 10

Page: 50 / 51

Manual ACM9_ARE i9 release V10.docx

5.

FCC Statement

5.1

ACM 9

Valid for ACM 9 – EtherCAT, ACM 9 – Profinet, ACM 9 – Ethernet/IP

Federal Communications Commissions (FCC) Statement
§15.21

You are cautioned that changes or modifications not expressly approved by the part responsible
for compliance could void the user’s authority to operate the equipment.

§15.105

Information to the user.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

5.2

ARE i9

Valid for ARE i9 – LF, ARE i9 –hdx - SEMI, ARE i9 - HF

Federal Communications Commissions (FCC) Statement
§15.21

You are cautioned that changes or modifications not expressly approved by the part responsible
for compliance could void the user’s authority to operate the equipment.

§15.105

Information to the user.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

6.

Release, Change Protocol

Revision:

Date:

Changes:

Author:

01

21.09.2020

Release first edition

NK

02

29.09.2020

Details added

NK

03

12.10.2020

Details added

NK

04

22.11.2020

Details added

NK

05

09.12.2020

FCC statement added

NK

06

06.01.2021

ACM 9 serial interface description added

NK

07

16.03.2021

EtherCAT nomenclature changed, Description files clarification

NK

08

23.03.2021

EtherCAT license statement updated

NK

09

20.10.2021

Read range for space contraints added

NK

10

17.10.2022

ARE i9x section added

NK

«
...
48
49
50
51
»

Summary of Contents for ACM 9




















































Reviews:

No comments

Related manuals for ACM 9

imageRUNNER ADVANCE C9075S PRO

Brand: Canon Pages: 20

Brand: Fancom Pages: 31

Brand: 3M Pages: 90

M16/RM N.C. DN 65 EEX

Brand: Madas Pages: 44

Brand: Baier Pages: 20

Brand: Anilam Pages: 31

Brand: Rinnai Pages: 7

Brand: Partlow Pages: 49

Brand: Ascon tecnologic Pages: 11

Brand: ROBOT3T Pages: 21

Brand: StudioComm Pages: 61

Brand: B meters Pages: 2

Brand: Black Stone Pages: 2

Brand: Vega Pages: 28

Brand: WATSON Pages: 16

Brand: Danfoss Pages: 16

Brand: CAME Pages: 18

Brand: KATO VISION Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands