AEG A18SRADBL, Original Instructions Manual

Page: 16 / 20

16
COMPATIBLE BATTERY PACKS (NOT INCLUDED)
L1820R
L1820S
A18FB2
L1825R
L1830R-X5
A18B4
L1840R
A18FB4
L1850R
A18FB5
L1860R
L1860R-X5
L1890R
Use AEG 18V battery and charger only
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury. Save all warnings and instruction
for future reference.
RIGHT ANGLE DRILL SAFETY WARNINGS
Safety instructions for all operations
Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory or
fasteners may contact hidden wiring. Cutting accessory or
fasteners contacting a “live” wire may make exposed metal parts of
the power tool “live” and could give the operator an electric shock.
Safety instructions when using long drill bits
Never operate at higher speed than the maximum speed rating
of the drill bit. At higher speeds, the bit is likely to bend if allowed
to rotate freely without contacting the workpiece, resulting in
personal injury.
Always start drilling at low speed and with the bit tip in contact
with the workpiece. At higher speeds, the bit is likely to bend if
allowed to rotate freely without contacting the workpiece, resulting in
personal injury.
Apply pressure only in direct line with the bit and do not apply
excessive pressure. Bits can bend causing breakage or loss of
control, resulting in personal injury.
Ambient temperature range for tool during operation is between 0°C
and 40°C.
Ambient temperature range for tool storage is between 0°C and
40°C.
The recommended ambient temperature range for the charging
system during charging is between 10°C and 38°C.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the product. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy non-
slip footwear, helmet and ear defenders.
The dust produced when using this product may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g.
asbestos).
Do not direct the light beam at persons or animals and do not stare
into the light beam yourself (not even from a distance). Staring into
the light beam may result in serious injury or vision loss.
TECHNICAL DATA A18SRADBL
Type Right angle drill
Drilling capacity in steel 10 mm
Drilling capacity in wood 38 mm
Wood screws (without pre-drilling) 6.5 mm
No-load speed, 1st gear 0-500 min
-1
No-load speed, 2nd gear 0-1,900 min
-1
Max torque 42.4 Nm
Battery voltage 18 V
Drill chuck range 0.8-10 mm
Weight without battery pack 1.0 kg
Noise/Vibration Information
Measured values determined according to EN 62841
A-weighted sound pressure level (Uncertainty K= 5 dB(A))
L
WA
= 82.0 dB(A)
A-weighted sound power level (Uncertainty K=5 dB(A)) L
pA
= 71.0 dB(A)
Wear ear protection.
Total vibration values (vector sum in the three axes) determined according to EN
62841
Drilling into metal
a
h
= 2.5 m/s
2
Uncertainty K 1.5 m/s
2
WARNING!
The declared vibration total values and the declared noise emission values given in this instruction manual have been measured in
accordance with a standardised test and may be used to compare one tool with another. They may be used for a preliminary assessment of
exposure.
The declared vibration and noise emission values represent the main applications of the tool. However, if the tool is used for different
applications, used with different accessories, or poorly maintained, the vibration and noise emission may differ. These conditions may
significantly increase the exposure levels over the total working period.
An estimation of the level of exposure to vibration and noise should take into account the times when the tool is turned off or when it is
running idle. These conditions may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and noise, such as maintaining the tool and the
accessories, keeping the hands warm (in case of vibration), and organising work patterns.