background image

11

INSTALLING THE COOKER HOOD

Please ensure that when the appliance is installed it
is easily accessible to an engineer in the event of a
breakdown.

All installations must comply with the
local authorities requirements for the
discharge of exhaust air.

Incorrect installation may affect the
safety of this cooker hood.

Installation Requirements

Before installation check the wall to
which the cooker hood is to be fitted for
electric cables, water pipes or gas.

The  cooker  hood  is  designed  to  be  fixed  to  any  rigid
vertical surface over a cooking area, and can be used in
the  extraction  (ducted  to  the  outside)  or  recirculation
(internal recycling) mode.

The Installation work must be undertaken by a qualified
and competent person. The manufacturer disclaims any
responsibility to damages due to incorrect installation of
the cooker hood or if the cooker hood is not installed in
compliance with relevant regulations controlling this type
of installation.

Unpacking

Before unpacking the cooker hood position the carton
with  the  arrows  pointing  upwards  as  illustrated  on  the
carton.

The  canopy  is  supplied  with  the  following
components for installation:

1 No. Canopy including controls and worktop illumination (C).
1 No. Telescopic chimney stack complete with fan motor (A).
1 No. Flange 120mm (F).
1 No. Collar 120-125mm
1 No. Venting grille (G).
1 No. Spigot (R).
1 No. Ducting conversion bend (W)
1 No. Support Rod (B)

S

F

G

R

W

B

Summary of Contents for 2020 D





















Reviews: