background image

10

INSTALLATION INSTRUCTIONS

It is dangerous to alter the specifications or attempt to modify this product in any way.

Technical Information
DIMENSIONS

HEIGHT (CANOPY):

73 mm

HEIGHT (CHIMNEY):

450-850 mm

WIDTH (CANOPY):

898 mm

WIDTH (CHIMNEY):

Ø200-Ø270 mm

GROSS:

24.00 kg

NET:

19,40 kg

ELECTRICAL SUPPLY:

220-240 V (50 Hz)

POWER CONSUMPTION:

215 W

FAN MOTOR:

175 W

LAMP:

(2x20W) HALOGEN Ø 35 mm GUA

40 W

SUITABLE FOR INSTALLATION
ABOVE:

ELECTRIC HOB:

7 KW

GAS HOB:

10 KW

SLOT-IN GAS COOKER

13.5 KW

SLOT-IN ELECTRIC COOKER

12.4 KW

Note: CE Marking certifies that this appliance complies with the requirements
laid  down  in  EEC  directive  89:336.  (Electromagnetic  compatibility)  and
subsequent modifications and Low Voltage directive 72/23/E.

ELECTRICAL CONNECTIONS

This appliance must be earthed

Electrical Requirements

Any permanent electrical installation must
comply with the latest I.E.E. Regulations and
local Electricity Board regulations. For your own
safety this should be undertaken by a qualified
electrician e.g. your local Electricity Board, or a
contractor who is on the roll of the National
Inspection Council for Electrical Installation
Contracting (NICEIC).

Electrical Connection

Before connecting to the mains supply ensure
that the mains voltage corresponds to the
voltage on the rating plate inside the cooker
hood.

This appliance is fitted with a 3 core mains
cable and must be permanently connected to
the electricity supply via a double-pole switch
having 3mm minimum contact gap on each
pole. A Switched Fuse Connection Unit to
BS1363 Part 4, fitted with a 3 Amp fuse, is a
recommended mains supply connection
accessory to ensure compliance with the Safety
Requirements applicable to fixed wiring
instructions.

This appliance conforms to BS 800: 1988 and
EEC Directive No. 78 308 regarding
suppression of radio and television
interference.

Summary of Contents for 2020 D





















Reviews: