background image

CONNECTING THE DOME LIGHTS

The dome lights in the video monitor require three connections to the vehicle's wiring. There are two
common types of dome light circuits used, positive or negative switched system. Positive switched
systems supply voltage to the interior lights to turn on, negative switched systems apply ground to
illuminate the bulbs.
To determine which system you have to locate the wires at the dome light:
On a positive switched system, with all the doors closed and the lights out, both wires at the dome light will
rest at ground. When the light is activated, one of these wires will switch to +12 vdc. This is the vehicle's
switching wire.
On a negative switched system, with all the doors closed and the lights out, both wires at the dome light will
rest at + 12vdc. When the light is activated, one of these wires will switch to ground. This is the vehicle’s
switching wire.

For positive systems, connect the violet / brown (Lamp auto) wire to the vehicle's switched wire. Then
connect the red / black (lamp on) wire to a fused constant 12 volt source and the black / red (lamp
common) wire to a good ground. Positive systems are commonly found on Ford vehicles.

For negative systems, connect the violet / brown (Lamp auto) wire to the vehicle's switched wire. Then
connect the red / black (lamp on) wire to a good ground and the black / red (lamp common) wire to fused
constant 12 volt source. Negative systems are commonly found on General Motors and import vehicles.

Some vehicles which incorporate transistorized control of the dome light circuit, such as the 1999

Dodge Caravan, may require that the violet / brown (Lamp auto) wire be connected to the door pin switch
wire, as the additional current draw of the monitor's lights may not be supported by the output of the
vehicles body control computer.

Note:

Positive Switched Dome Lighting

Red / black - Lamp on

Factory Dome light circuit

To 12 pin

connector

on Monitor

To

constant

+12vdc

To

constant

+12vdc

Black / red - Lamp common
Purple / brown - Lamp Auto

Factory Door ajar
switch or Body
Control computer

10

Fused

Summary of Contents for ADV38













Reviews: