Advantech PCE-7214 User Manual Download Page 10 | Manualshive

Page: 10 / 90

background image

PCE-7214 User Manual

x

Table B.9: Power LED and Keyboard Lock Connector (JFP3 /

PWR_LED & KEY LOCK) ........................................ 70

B.10

External Speaker Connector (JFP2 / SPEAKER) ................................... 71

Table B.10:External Speaker Connector (JFP2 / SPEAKER) .... 71

B.11

Reset Connector (JFP1 / RESET) .......................................................... 71

Table B.11:Reset connector (JFP1 / RESET) ............................ 71

B.12

HDD LED (JFP2 / HDDLED)................................................................... 71

Table B.12:Reset connector (JFP1 / RESET) ............................ 71

B.13

ATX Soft Power Switch (JFP1 / PWR_SW)............................................ 72

Table B.13:Reset connector (JFP1 / RESET) ............................ 72

B.14

Hi-definition audio Link connector (HDAUD1)......................................... 72

Table B.14:Hi-definition audio link connector (HDAUD1) ........... 72

B.15

SM Bus Connector (JFP2 / SNMP)......................................................... 72

Table B.15:SM bus connector (JFP2 / SNMP) ........................... 72

B.16

LAN1 and LAN2 LED connector (LANLED1).......................................... 73

Table B.16:LAN1 and LAN2 LED connector (LANLED1) ........... 73

B.17

GPIO header (GPIO1) ............................................................................ 73

Table B.17:GPIO header (GPIO1).............................................. 73

B.18

System I/O Ports..................................................................................... 74

Table B.18:System I/O ports....................................................... 74

B.19

DMA Channel Assignments .................................................................... 75

Table B.19:DMA channel assignments....................................... 75

B.20

Interrupt Assignments ............................................................................. 75

Table B.20:Interrupt assignments............................................... 75

B.21

1st MB Memory Map............................................................................... 75

Table B.21:1st MB memory map ................................................ 75

B.22

PCI Bus Map........................................................................................... 76

Table B.22:PCI bus map............................................................. 76

Appendix C

Programming the GPIO and Watchdog
Timer

.................................................. 77

C.1

Supported GPIO Register ....................................................................... 78
C.1.1 GPIO Registers........................................................................... 78
C.1.2 GPIO Example program-1 .......................................................... 79

«
...
8
9
10
11
12
...
»

Summary of Contents for PCE-7214



























































































Reviews:

No comments

Related manuals for PCE-7214

Brand: IEI Technology Pages: 21

Brand: National Instruments Pages: 9

FIELDPOINT FP-1600

Brand: National Instruments Pages: 8

Brand: XESS Pages: 23

Brand: Oracle Pages: 24

Brand: Maxim Pages: 14

Parallel Printer Card PIOC

Brand: B&B Electronics Pages: 16

RCO-3000 Series

Brand: C&T Solution Pages: 96

Brand: EVOC Pages: 57

Brand: Idis Pages: 22

DEEP LEARNING PLUS

Brand: Concept Pro Pages: 28

Brand: Ubiquiti Pages: 13

VIGI NVR1004H-4P

Brand: TP-Link Pages: 2

IP-Logic ZIG-IPPRO-RX

Brand: Zigen Pages: 4

Brand: XtendLan Pages: 21

Brand: Ariesys Pages: 10

Brand: Navitar Pages: 1

Brand: Crown Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands