manualshive.com logo in svg

Advantech PCA-6751 Series, User Manual

Share
Download
Advantech PCA-6751 Series User Manual Download Page 43

34

PCA-6751 Series  User's Manual

Boot Up System Speed

High

Sets the speed to high

Low

Sets the speed to low

IDE HDD Block Mode

Enabled

Enable IDE HDD Block Mode. BIOS will detect the block size
of the HDD and send a block command automatically.

Disabled

Disable IDE HDD Block Mode

Gate A20 option

Normal

The A20 signal is controlled by the keyboard controller or
chipset hardware

Fast

Default: Fast. The A20 signal is controlled by Port 92 or
chipset specific method.

Typematic Rate Setting

The typematic rate determines the characters per second accepted by
the computer. Typematic Rate setting enables or disables the typemat-
ic rate.

Typematic Rate (Char/Sec)

BIOS accepts the following input values (character/second) for
Typematic Rate: 6, 8, 10, 12, 15, 20, 24, 30.

Typematic Delay (msec)

When holding down a key, the Typematic Delay is the time interval
between the appearance of the first and second characters. The input
values (msec) for this category are: 250, 500, 750, 1000.

Summary of Contents for PCA-6751 Series
















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands