Advantech PCA-6743 User Manual Download Page 43

Page: 43 / 70

PCA-6743 User Manual

This item allows to choose performing USB device in [full/low speed] or [high
speed] mode.

–

USB Keyboard Function [Enabled]

Enable or disable legacy support of USB keyboard

–

USB Mouse Function [Enabled]

Enable or disable legacy support of USB mouse

–

USB Storage Function [Enabled]

Enable or disable legacy support of USB mass storage

–

Delay for USB storage [3]

This item allows to choose from 0 to 10 secs.



PDX-600 IDE Legacy mode [Native Mode]

This item enables Vortex86DX SOC IDE as legacy or native mode.



Onboard LAN Control [Enabled]

This item is enabled or disabled that onboard of LAN controller.



Onboard LAN ROM [Disabled]

This item allows user to choose the way that LAN boot ROM work



PDX-600 CPU Divided [[Divide 1]

This item allows to do CPU speed divided

3.2.5

Integrated Peripherals

Note!

Please set PDX-600 IDE Legacy mode to [Legacy Mode], while you
install Windows 98.

Summary of Contents for PCA-6743







































































Search results

Summary of Contents for PCA-6743

Reviews:

Related manuals for PCA-6743

Brands by name

Popular brands

Advantech PCA-6743, User Manual

Search results

Summary of Contents for PCA-6743

Reviews:

Related manuals for PCA-6743

Brands by name

Popular brands