manualshive.com logo in svg

Advantech MOS-1120Y Series, User Manual, Page: 2 / 34

Share
Download
Advantech MOS-1120Y Series User Manual Download Page 2

MOS-1120Y/1121Y Series User Manual

ii

Copyright

This document is copyrighted 2018 by Advantech Co. Ltd. All rights are reserved.
Advantech Co., Ltd. reserves the right to alter the products described in this manual
at any time without notice. No part of this manual may be reproduced, copied, trans-
lated, or transmitted in any form or by any means without the prior written permission
of Advantech. The information provided in this manual is intended to be accurate and
reliable. However, Advantech assumes no responsibility for use of this manual, nor
for any infringements on the rights of third parties that may result from its use. 

Acknowledgments

MOS-1120Y/1121Y-140xE is a trademark of Advantech Corporation.
All other product names or trademarks are properties of their respective owners.

Online Technical Support

For technical support and service, please visit our support website at
http://support.advantech.com.cn

Part No. 2001112000

Edition 1

Printed in China

October 2018

Summary of Contents for MOS-1120Y Series



































Reviews:

No comments