Advantech FWA-3050 User Manual Download Page 48

Page: 48 / 72

User Manual FWA-3050

_ v0.2 20200207.docx

2017

Page 48

5.2.2.7

Platform Management

This sub menu allows you to change the settings used for related CPU utilization setting.

The default configuration for CPU was optimized setting for getting better performance for networking, so it
is not recommend to change it.

Figure 26 Platform Setup: Platform Management

Group

Setup item

Access /

Options

Description

None

EIST

Enable

Disable

Enable or disable BIOS support for
Enhanced Intel SpeedStep Technology,
When enabled, OS sets CPU frequency
according load. When disabled, CPU
frequency is set at max non-turbo.

P-state

coordination

HW_ALL

HW_ALL (hardware) coordination is
recommended over SW_ALL and SW_ANY
(software coordination).

CPU C6 report

Enable

Disable

Enable/Disable CPU C6(ACPI C2) report to
OS Recommended to be enabled.

Package C State

limit

C0/C1 state

C2 state

C6(non

Retention) state

C6(Retention)

state

Package C State limit. The "waking-up
time" will be longer if Package C state limit
setting is deep C state support.

Summary of Contents for FWA-3050


































































Search results

Summary of Contents for FWA-3050

Reviews:

Related manuals for FWA-3050

Brands by name

Popular brands

Advantech FWA-3050, User Manual

Search results

Summary of Contents for FWA-3050

Reviews:

Related manuals for FWA-3050

Brands by name

Popular brands