manualshive.com logo in svg

Advantech EKI-7556MI, User Manual, Page: 26 / 105

Share
Download
Advantech EKI-7556MI User Manual Download Page 26

2.6 X-Ring 

Application 

 

The industrial switch supports the X-Ring protocol that can help the network system recover from 
network connection failure within 10ms and make the network system more reliable. The X-Ring 
algorithm is similar to Spanning Tree Protocol (STP) and Rapid STP (RSTP) algorithm but its recovery 
time is less than STP/RSTP. The figure below is a sample of X-Ring application. 
 
 

 

 
 

Note 

The Ethernet switches with firmware version before v3.0 use the X-Ring 
function that has the limitation as follows. However, the one with firmware 
version after v3.0 (included) use the X-Ring Pro function that gets rid of 
the limitation. 
 
1.  The X-Ring is supposed to recover from connection failure within 

10ms when the amount of the connected devices of the X-Ring group 
is less than 50. 

 

EKI-7556MI_Manual           

                              

26 

Summary of Contents for EKI-7556MI










































































































Reviews:

No comments