Advantech EKI-1334 User Manual Download Page 57

Page: 57 / 72

EKI-1334 User Manual

Chapter 3

dvanced

onfiguration

OpenVPN Settings

Name

Description

Default

Enable

Click Enable

Enable

Tunnel Name

Set Tunnel Name

PPTP_TUNNEL_1

PPTP Server

Set PPTP Server Address

Blank

Username

Set Server Username

Blank

Password

Set Server’s Password

Blank

Startup Mode:

Set Startup Modes: Auto Acti-
vated, Trigged by Data, Manu-
ally Activated

Auto Activated

Authencation Type

Set Authencation Type: CHAP,
PAP, MS-CHAPv1, MS-
CHAPv2

Auto

Local IP Address

Set Local IP Address

Blank

Remote IP Address

Set Remote IP Address

Blank

Remote Subnet

Set Remote Subnet

Blank

Remote Subnet Net Mask

Set Remote Subnet Net Mask 255.255.255.0

Link Detection Interval

Set Link Detection Interval

Max Retries for Link Detection

Set Max Retries for Link
Detection

Enable NAT

Click Enable NAT

Blank

Enable MPPE

Click Enable MPPE

Blank

Enable MPPC

Click Enable MPPC

Blank

MTU

Set MTU parameters

1500

MRU

Set MRU parameters

1500

Enable Debug Mode

Click Enable Debug Mode

Blank

Expert Options

For Advantech R&D only

Blank

Summary of Contents for EKI-1334









































































Search results

Summary of Contents for EKI-1334

Reviews:

Related manuals for EKI-1334

Brands by name

Popular brands

Advantech EKI-1334, User Manual

Search results

Summary of Contents for EKI-1334

Reviews:

Related manuals for EKI-1334

Brands by name

Popular brands